TP-Link CPE710 | 5GHz AC 867Mbps Long Range Gigabit Outdoor CPE for PtP and PtMP Transmission | Point to Point Wireless Bridge | 23dBi | Passive PoE Powered w/Free PoE Injector | Pharos Control

Worked better than hoped. I Purchased 3 of these to replace and old 2.4Ghz Tycon. I am using and a chain of intermediary routers and repeaters. Configured 1 as the AP and attached it to the roof. The was placed on the workshop some 350 feet away. Both directed at each other. I now get full line rate to the internet at some 360MB which is my rate through my provider.My third was placed as a client 450 feet away through some trees at a 110 degree agle from the way the AP is pointing at the Workshop. Slightly behind it to the right. The roof that the AP is mounted on cuts the line of site and the wood sheething under the shingles is foil wrapped. Surprisingly I get 135Mbits to this Client. Using the wavelink High gain routers to reach the old network I was only receiving about 4-5Mbits. Very pleased as this runs wifi for a remote wireless gate and a Wireless Camera.Just ordered a 4th to place in the barn around 275 feet away.Note: When first installed, I had stability issues. It was bouncing connection where the AP would be seen by the client for a bit then it would not. I decided to upgrade the firmware to the latest on the Client. The upload of the binary file completed but it appears I lost connection during the write. to flash. This corrupted the units software. The unit never came back.After investingations and using the third unit I had bought. I found the 100 ft Cat 6 cable was causing issues. Isolated out and put in a new cable and everything came up clean.The problem was the original CPE710 was corrupted during the image upgrade. I located a firmware upgrade procedure on the TPLINK website for the Pharos equipment and was able to do a reflash of the unit with the newest Binary file. It is revived configured and the unit is back working.Suggestion: TPLINK should add the short procedure to relash a unit if corrupted downloads to their manuals.

Wow these are great. I read other reviews, and was unsure if it would work for me. My unit is a 600 foot run thru heavy Oaks, and it works perfect. Very configurable for your needs. Minor IT knowledge to get it going. Now Mom-in-law does not have a $75 internet bill. I did buy 2 of these. One at my house, and one at the other end. Hooked it up to a wireless router, works great. Very happy. But can be used also as an extender with only one unit.

Excelente, Muy buena calidad!

I installed a pair of these last September at my rural home because I had to backhaul my Starlink connection from my pole barn (where I had clear line-of-sight) to the house (which has no view of the sky due to all the trees). One CPE710 is hanging off the side of my barn connected to the Starlink router, and the other is pole-mounted behind the house with some Cat6 running through a conduit to my house router/AP. They've been through snow, rain, and ice storms. Temps have ranged from the low 90's down into sub-zero territory, and reliability has been 100%.If you have zero networking experience then you might struggle a bit as setup is more complex than a wifi router with a phone app. Since I already had access points on both ends of the p2p connection, I used a separate SSID and wifi channel specifically for the pair of CPE710s, and I set the SSID to hidden. Otherwise you can get clients trying to connect to the CPE710 instead of your preferred access point, and the result will be some stability issues. For my use case I connected via ethernet, assigned static IPs, set one to AP mode, one to client mode, punched in the SSIDs/keys, tweaked some settings a little bit, and I was off and running at full-speed.As I type this, they have been up for almost 3 months without a reboot and transferred untold terabytes of data, so I have zero complaints. I do have them both running through a small UPS which is plenty to let them keep going through a moderate power outage.

I purchased this to provide internet to our new Airbnb that is about 1/2 mile away from our home with a clear line of sight. I was hopeful this would save the extra expense of a second ISP and I was shocked at how well it worked. I set up one unit as the AP and the second as a Client. That process took less than 15 minutes. I mounted the AP unit on our home and took the second unit down the street. To my amazement and delight I began receiving an adequate signal inside the house! Once mounted outside I was able to stream video on three TVs perfectly. There was no drop off in speed from our home. I believe there may be some confusion in the negative reviews. You must purchase two units to send and receive.

I received hardware version 2.0, apparently the current HW version is 2.8. Device does not support WPA3. The mount is a little rickety and held on by only one hose clamp even though the device is fairly front-heavy.

TP-Link makes it very difficult to deal with them if a product under warranty is defective. They demand all kinds of proof of purchase, make you submit registration and other forms related to the purchase. They make you wait and they are slow to respond. The worst is that if your item is defective and under warranty, they make you pay to send it back to them before they will consider sending you a replacement. Shipping is, in most cases, is significant to the cost of the product. In short, their "warranty" is pretty much worthless: costs way too much in time and money to use there products......A bad business model, and certainly not an industry standard.

El producto es muy buen, lo estoy usando para hacer llegar el internet de un edificio a otro. He visto señales de hasta 1km